Conserte seus objetos Comunidade Loja

Canon PowerShot SD1200 IS Motherboard

Introdução

Use this guide to access the motherboard to reseat connections on the motherboard or to remove the motherboard for replacement.

O que você precisa

  1. Canon PowerShot SD1200 IS Motherboard, Front and Rear Covers: passo 1, imagem 1 %32

    • Remove the battery.

    Editar

  2. Canon PowerShot SD1200 IS Motherboard: passo 2, imagem 1 %32 Canon PowerShot SD1200 IS Motherboard: passo 2, imagem 2 %32 Canon PowerShot SD1200 IS Motherboard: passo 2, imagem 3 %32

    • Remove the two screws from the side of the camera casing with the strap. (4mm Phillips 00)

    • Remove the two screws from the bottom of the camera. (4mm Phillips 00)

    • Remove the two screws from the right side of the camera opposite the strap. (2mm Phillips 00)

    Editar

  3. Canon PowerShot SD1200 IS Motherboard: passo 3, imagem 1 %32 Canon PowerShot SD1200 IS Motherboard: passo 3, imagem 2 %32

    • Pull off the front cover.

    • If the top of the cover sticks, use gentle downward pressure on the retention clips above the lens to release.

    • Remove the back cover.

    Editar

  5. Canon PowerShot SD1200 IS Motherboard, Motherboard: passo 4, imagem 1 %32

    • Remove the microphone connector by gripping it with the tool and gently, with a wiggling motion, pull it out.

    • Pull the connector straight out by the white connector. Pulling on the wires will damage them.

    Editar

  6. Canon PowerShot SD1200 IS Motherboard: passo 5, imagem 1 %32

    • Lift off the mechanical shutter button assembly.

    Editar

  7. Canon PowerShot SD1200 IS Motherboard: passo 6, imagem 1 %32 Canon PowerShot SD1200 IS Motherboard: passo 6, imagem 2 %32

    • Use the spudger to lift the tab on the Zero Insertion Force (ZIF) connector located at the bottom of the motherboard.

    • Be sure you are prying up on the hinged retaining flap, not the connector itself.

    • Slide out the ribbon cable.

    • Use the spudger to pry up each side of the Flat-Topped Connectors

    Editar

  8. Canon PowerShot SD1200 IS Motherboard: passo 7, imagem 1 %32

    • Remove the press fit ribbon cable by prying upward with spudger tool.

    • It is not necessary to remove the Lens or Flash Assemblies to remove the motherboard.

    Editar

  9. Canon PowerShot SD1200 IS Motherboard: passo 8, imagem 1 %32

    • Remove the bottom right screw from the motherboard. (4mm Phillips 00)

    • Remove top and lower left black screws from the motherboard. (2.5mm Phillips 00)

    Editar

  10. Canon PowerShot SD1200 IS Motherboard: passo 9, imagem 1 %32

    • Lift out the motherboard.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

com 4 outros contribuidores

Jeff Casper

Membro desde: 09/15/16

848 Reputação

Autoria de 7 guias

Emblemas: 18

+15 outros emblemas

Equipe

USF Tampa, Team 17-5, Blackwell Fall 2016 Membro de USF Tampa, Team 17-5, Blackwell Fall 2016

USFT-BLACKWELL-F16S17G5

Membros da 3

Autoria de 7 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 6

Duração total: 394