Conserte seus objetos

Direito de executar reparos

Loja

Este guia tem alterações mais recentes. Mudar para a última versão não verificada.

Canon PowerShot SD1000 Broken Flash Unit Replacement

Escrito Por: Phillip Phung (e 10 outros contribuidores)
  • Comentários: 0
  • Favoritos: 0
  • Execuções: 1

Dificuldade

Moderado

Passos

16

Tempo necessário

Sugerir um tempo??

Partes

4

Sinalizadores

2

Grammar Police

Polícia gramatical

Abrace seu professor de Inglês interior e ajude a melhorar a gramática deste guia!

Needs Better Images

Precisa de melhores imagens

Melhores fotos vão melhorar este guia. Ajude tirando, editando ou enviando novas delas!

Ferramentas

Comprar estas ferramentas

Peças

Nenhum componente especificado.

  1. Remove the two screws from the side panel closest to the camera lens. Note: These screws are 2.9 mm long.

    • Remove the two screws from the side panel closest to the camera lens.

    • Note: These screws are 2.9 mm long.

    Editar

  2. Remove the two screws from the camera bottom panel.

    • Remove the two screws from the camera bottom panel.

    • Note: These screws are 2.9 mm long.

    Editar

  3. Remove the 2 screws from the side panel farthest from the lens.

    • Remove the 2 screws from the side panel farthest from the lens.

    • Note: These screws are 2.9 mm long.

    Editar

  4. Pull the back panel away from the camera body, starting at the end with the function buttons.

    • Pull the back panel away from the camera body, starting at the end with the function buttons.

    Editar

  5. Remove the small cover panel and attached wrist strap mount.

    • Remove the small cover panel and attached wrist strap mount.

    Editar

  6. Remove the front cover by gently pulling it away from the camera body.

    • Remove the front cover by gently pulling it away from the camera body.

    Editar

  8. Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

    • Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

    Editar

  9. Remove the 2 screws located at the top of the LCD panel.

    • Remove the 2 screws located at the top of the LCD panel.

    • Note: These screws are 2.4 mm long.

    Editar

  10. Pull up the metal frame surrounding LCD screen starting at the side of the camera. Pull up the metal frame surrounding LCD screen starting at the side of the camera.

    • Pull up the metal frame surrounding LCD screen starting at the side of the camera.

    Editar

  11. Push the metal frame away from the metal tab using the spudger, to detach the frame.

    • Push the metal frame away from the metal tab using the spudger, to detach the frame.

    • Rotate the metal frame upwards.

    • Note: The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

    Editar

  12. Carefully lift the metal frame from the camera. Remove the black LCD screen, leaving the thin lens pieces in place.

    • Carefully lift the metal frame from the camera.

    • Remove the black LCD screen, leaving the thin lens pieces in place.

    • Note: BE CAREFUL, both components are attached by an orange connector ribbon and cannot be removed yet!

    Editar

  13. Carefully pull on the orange connector ribbon to disconnect the LCD screen. The LCD screen can be pulled out of the frame before disconnecting its connector ribbon. Note: Tweezers are helpful to disconnect the ribbon

    • Carefully pull on the orange connector ribbon to disconnect the LCD screen.

    • The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

    • Note: Tweezers are helpful to disconnect the ribbon

    Editar

  14. Remove the metal frame on the side closest to the flash mechanism. This will expose the screw securing the flash assembly. Remove the metal frame on the side closest to the flash mechanism. This will expose the screw securing the flash assembly.

    • Remove the metal frame on the side closest to the flash mechanism. This will expose the screw securing the flash assembly.

    Editar

  15. Remove the screw securing the flash assembly.

    • Remove the screw securing the flash assembly.

    • Note: The screw is 2.4mm long.

    Editar

  16. Use the spudger to carefully disconnect the flash assembly ribbon from the black connector lock.

    • Use the spudger to carefully disconnect the flash assembly ribbon from the black connector lock.

    Editar

  17. Remove the flash assembly. Note: BE CAREFUL, when handling the flash assembly; touching the capacitor (the black cylinder) could shock you

    • Remove the flash assembly.

    • Note: BE CAREFUL, when handling the flash assembly; touching the capacitor (the black cylinder) could shock you

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Autor

com 10 outros contribuidores

Phillip Phung

Membro desde: 19/01/2012

513 Reputação

9 Guias de autoria

Emblemas: 10

+7 outros emblemas

Equipe

Cal Poly, Team 8-18, Maness Winter 2012 Membro de Cal Poly, Team 8-18, Maness Winter 2012

CPSU-MANESS-W12S8G18

4 Membros

10 Guias de autoria

0 comentários

Adicionar um comentário

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 3

Duração total: 2,472