Peças

Não são necessárias peças.

Remove the two screws from the side panel closest to the camera lens. Note: These screws are 2.9 mm long.
  • Remove the two screws from the side panel closest to the camera lens.

  • Note: These screws are 2.9 mm long.

Adicionar comentário

Remove the two screws from the camera bottom panel.
  • Remove the two screws from the camera bottom panel.

  • Note: These screws are 2.9 mm long.

Adicionar comentário

Remove the 2 screws from the side panel farthest from the lens.
  • Remove the 2 screws from the side panel farthest from the lens.

  • Note: These screws are 2.9 mm long.

Adicionar comentário

Pull the back panel away from the camera body, starting at the end with the function buttons.
  • Pull the back panel away from the camera body, starting at the end with the function buttons.

Adicionar comentário

Remove the small cover panel and attached wrist strap mount.
  • Remove the small cover panel and attached wrist strap mount.

Adicionar comentário

Remove the front cover by gently pulling it away from the camera body.
  • Remove the front cover by gently pulling it away from the camera body.

Adicionar comentário

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.
  • Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

Adicionar comentário

Remove the 2 screws located at the top of the LCD panel.
  • Remove the 2 screws located at the top of the LCD panel.

  • Note: These screws are 2.4 mm long.

Adicionar comentário

Pull up the metal frame surrounding LCD screen starting at the side of the camera. Pull up the metal frame surrounding LCD screen starting at the side of the camera.
  • Pull up the metal frame surrounding LCD screen starting at the side of the camera.

Adicionar comentário

Push the metal frame away from the metal tab using the spudger, to detach the frame.
  • Push the metal frame away from the metal tab using the spudger, to detach the frame.

  • Rotate the metal frame upwards.

  • Note: The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

Adicionar comentário

Carefully lift the metal frame from the camera. Remove the black LCD screen, leaving the thin lens pieces in place.
  • Carefully lift the metal frame from the camera.

  • Remove the black LCD screen, leaving the thin lens pieces in place.

  • Note: BE CAREFUL, both components are attached by an orange connector ribbon and cannot be removed yet!

Adicionar comentário

Carefully pull on the orange connector ribbon to disconnect the LCD screen. The LCD screen can be pulled out of the frame before disconnecting its connector ribbon. Note: Tweezers are helpful to disconnect the ribbon
  • Carefully pull on the orange connector ribbon to disconnect the LCD screen.

  • The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

  • Note: Tweezers are helpful to disconnect the ribbon

Adicionar comentário

Remove the metal frame on the side closest to the flash mechanism. This will  expose the screw securing the flash assembly. Remove the metal frame on the side closest to the flash mechanism. This will  expose the screw securing the flash assembly.
  • Remove the metal frame on the side closest to the flash mechanism. This will expose the screw securing the flash assembly.

Adicionar comentário

Remove the screw securing the flash assembly.
  • Remove the screw securing the flash assembly.

  • Note: The screw is 2.4mm long.

Adicionar comentário

Use the spudger to carefully disconnect the flash assembly ribbon from the black connector lock.
  • Use the spudger to carefully disconnect the flash assembly ribbon from the black connector lock.

Adicionar comentário

Remove the flash assembly. Note: BE CAREFUL, when handling the flash assembly; touching the capacitor (the black cylinder) could shock you
  • Remove the flash assembly.

  • Note: BE CAREFUL, when handling the flash assembly; touching the capacitor (the black cylinder) could shock you

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Phillip Phung

Member since: 19-01-2012

468 reputação

9 Guides authored

Equipe

Cal Poly, Team 8-18, Maness Winter 2012 Membro de Cal Poly, Team 8-18, Maness Winter 2012

CPSU-MANESS-W12S8G18

4 Membros

10 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 3

Todo: 2,398