Introdução

This guide will involve the removal of various screws, as well as detaching the two gold ribbons connecting the motherboard to the camera.

Peças

Não são necessárias peças.

Slide the switch on the battery cover labeled "CARD/BATT. OPEN." to the right.
  • Slide the switch on the battery cover labeled "CARD/BATT. OPEN." to the right.

  • While still holding the switch, pull the cover down, allowing it to release and open.

Adicionar comentário

Tilt the camera slightly to allow the batteries to fall out.
  • Tilt the camera slightly to allow the batteries to fall out.

Adicionar comentário

  • Press on and release the memory card to eject it.

Adicionar comentário

  • Unscrew the 5mm Phillips #00 screw from the bottom of the camera.

  • Make sure to keep the different size screws organized to make reassembling the camera simpler.

Adicionar comentário

  • Unscrew the three 2mm Phillips #00 screws that are located on the bottom of the camera.

Adicionar comentário

  • Remove the 4mm Phillips #00 screw that is located on the left side of the camera, if the display screen is facing you.

Adicionar comentário

  • Take out the 4mm Phillips #00 screw under the rubber flap on the right end of the camera.

Adicionar comentário

  • Remove the second battery cover on the bottom of camera.

  • Take the silver battery out of the camera.

Adicionar comentário

  • Remove the 4mm Phillips #00 screw on the inside of the flap that hides the battery and memory card slots.

  • Remove the light grey, plastic piece.

  • Remove the plastic portion of the battery flap cover. The metal piece will remain attached.

Adicionar comentário

  • Slightly pull on each side of the camera. It should loosen up and come apart.

  • If it does not pull apart right away, use a little more force.

  • Do not give up!

Adicionar comentário

  • Remove the back case of the camera by pulling from the top.

  • Be careful when pulling off the case. There is a delicate gold ribbon connecting the bottom of the camera to the back case.

Adicionar comentário

  • Remove the 4mm Phillips #00 screw from above the ribbon.

Adicionar comentário

  • Gently peel off the blue tape on the top of the LCD screen.

Adicionar comentário

  • Remove the 4mm Phillips #00 screw previously concealed by the blue tape.

Adicionar comentário

  • Gently lift the LCD screen off of the front casing by pulling up a tab on the side of the camera.

Adicionar comentário

  • Using a spudger, lift the grey tabs to allow the ribbon to slide out.

Adicionar comentário

  • Since the tabs have been lifted, the ribbon should now slide out out easily.

  • Be careful not to distort the ribbon in any way.

Adicionar comentário

  • Remove the 5mm Phillips #00 screw located above the small black piece on the right side of the mother board.

Adicionar comentário

  • Remove the 4mm Phillips #00 screw at the bottom of the black piece.

  • Detach the black piece that the screws previously held in place.

Adicionar comentário

  • Remove the 5mm Phillips #00 screw in the middle of the motherboard.

Adicionar comentário

  • Remove the 5mm Phillips #00 screw that holds the metal piece to the bottom of the camera .

Adicionar comentário

  • Remove the 5mm Phillips #00 screw that is located on the top of camera.

Adicionar comentário

  • Remove the 2mm Phillips #00 screw that is located on the far left of the motherboard.

  • Be careful not to damage the multiple adjacent orange ribbons.

Adicionar comentário

  • Remove the 5mm Phillips #00 screw near the bottom left of the motherboard.

Adicionar comentário

  • Using a spudger, unlock the locking mechanism that holds the lower orange ribbon in place.

  • Once unlocked, slide out the ribbon.

Adicionar comentário

  • Using a spudger, unlock the locking mechanism that holds the upper orange ribbon in place.

  • Once unlocked, slide out the ribbon.

Adicionar comentário

  • All that is required is to unsolder the few remaining wires. Then, the motherboard will be ready to be replaced!

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

2 outras pessoas concluíram este guia.

Tanner Coleman

Member since: 18-01-2013

25 reputação

2 Guides authored

Equipe

Cal Poly, Team 19-42, Regan Winter 2013 Membro de Cal Poly, Team 19-42, Regan Winter 2013

CPSU-REGAN-W13S19G42

4 Membros

6 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 3

Todo: 1,026