Introdução

Follow this guide to install the trackball in the Blackberry Pearl 8100.

Peças

Não são necessárias peças.

Before working on the phone, be sure that the phone is turned off. Begin by removing the back panel; this can be done by pressing the silver button on the backside of the Blackberry 8100, while simultaneously sliding the back panel off.
  • Before working on the phone, be sure that the phone is turned off.

  • Begin by removing the back panel; this can be done by pressing the silver button on the backside of the Blackberry 8100, while simultaneously sliding the back panel off.

Adicionar comentário

  • Remove the battery located directly below back panel.

Adicionar comentário

Using a 1.5 mm Hex screwdriver, remove the two screws that hold the two panels together.
  • Using a 1.5 mm Hex screwdriver, remove the two screws that hold the two panels together.

Adicionar comentário

Using the spudger, pry off the small portion of the casing located at the bottom of the phone. Using the spudger, pry off the small portion of the casing located at the bottom of the phone.
  • Using the spudger, pry off the small portion of the casing located at the bottom of the phone.

Adicionar comentário

Using the spudger, pry off the side casings one at a time by wedging it between the inner casing and the sides.
  • Using the spudger, pry off the side casings one at a time by wedging it between the inner casing and the sides.

Adicionar comentário

Using a 1.5mm Hex screwdriver, unscrew the two screws, located on the front of the phone, that connect the back and front panels.
  • Using a 1.5mm Hex screwdriver, unscrew the two screws, located on the front of the phone, that connect the back and front panels.

Adicionar comentário

Using the spudger, pry off the back body panel by wedging the spudger in between the front and back panels on the side face.  Remove the back body panel. Using the spudger, pry off the back body panel by wedging the spudger in between the front and back panels on the side face.  Remove the back body panel.
  • Using the spudger, pry off the back body panel by wedging the spudger in between the front and back panels on the side face. Remove the back body panel.

Adicionar comentário

Separate the logic board from the front panel.
  • Separate the logic board from the front panel.

Adicionar comentário

Gently remove the keyboard from front casing. It should snap out of place. Gently remove the keyboard from front casing. It should snap out of place.
  • Gently remove the keyboard from front casing. It should snap out of place.

Adicionar comentário

Remove the larger chrome ring holding the track ball in place by using the spudger to gently wedge the top ring away, approaching from the front face.
  • Remove the larger chrome ring holding the track ball in place by using the spudger to gently wedge the top ring away, approaching from the front face.

  • Some of these parts are fairly small and fragile; be sure to keep them in a safe place where they won't be damaged if you intend to reuse them.

Adicionar comentário

Remove the smaller chrome inner ring surrounding the trackball; it should be able to be simply lifted by hand.
  • Remove the smaller chrome inner ring surrounding the trackball; it should be able to be simply lifted by hand.

Adicionar comentário

Remove the trackball housing; it should be able to be removed by hand.
  • Remove the trackball housing; it should be able to be removed by hand.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

4 outras pessoas concluíram este guia.

Robert Cronin

Member since: 08-04-2010

520 reputação

6 Guides authored

Equipe

Cal Poly, Team 34-57, Forte Spring 2010 Membro de Cal Poly, Team 34-57, Forte Spring 2010

CPSU-FORTE-S10S34G57

5 Membros

6 Guides authored

why dissasemble the entire device, just remove the chrome ring....

Latios Eon - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 4

Últimos 30 dias: 10

Todo: 7,492