Conserte seus objetos Comunidade Loja

Black and Decker WP900 Motor Replacement

Introdução

This page gives instructions for disassembling the Black and Decker WP900 6-Inch Orbital Waxer and Polisher to the point where the motor can be fully removed and replaced.

O que você precisa

  1. Black and Decker WP900 Motor Replacement, Motor: passo 1, imagem 1 %32

    • Using the plastic tool, detach the handle tab as shown.

    • Make sure the device is unplugged.

    Editar

  2. Black and Decker WP900 Motor Replacement: passo 2, imagem 1 %32

    • Using the Philips #1 screwdriver, unscrew all of the screws. There should be 8-30mm screws to remove.

    • Be sure to keep track of where each screw was placed in the device for later reassembly.

    Editar

  3. Black and Decker WP900 Motor Replacement: passo 3, imagem 1 %32 Black and Decker WP900 Motor Replacement: passo 3, imagem 2 %32 Black and Decker WP900 Motor Replacement: passo 3, imagem 3 %32

    • Remove the back panel of the external casing, leaving all internal components resting in the front panel.

    • Remove the black handle from the main external casing.

    Editar

  5. Black and Decker WP900 Motor Replacement: passo 4, imagem 1 %32

    • Loosen the power cord and control panel. Using the Phillips #1 screwdriver, remove two 22mm screws.

    • The metal bracket will detach with the two screws.

    • Using the Flathead 3/32" screwdriver, remove two 22mm screws.

    Editar

  6. Black and Decker WP900 Motor Replacement: passo 5, imagem 1 %32 Black and Decker WP900 Motor Replacement: passo 5, imagem 2 %32

    • Gently pull the power cord out from the control module.

    • Remember, when you're reassembling the device, the black wire should be on the top.

    Editar

  7. Black and Decker WP900 Motor Replacement: passo 6, imagem 1 %32

    • Firmly grasping the motor, dislodge the internal components from the frontal external casing.

    • Switch and control panel are attached to the motor.

    Editar

  8. Black and Decker WP900 Motor Replacement: passo 7, imagem 1 %32 Black and Decker WP900 Motor Replacement: passo 7, imagem 2 %32

    • Using a Phillips #1 screwdriver, remove the two 22mm screws securing the brush assembly to the motor.

    Editar

  9. Black and Decker WP900 Motor Replacement: passo 8, imagem 1 %32 Black and Decker WP900 Motor Replacement: passo 8, imagem 2 %32

    • To fully remove the brush assembly from the motor, push the brushes (enclosed in the gold ribbing) outward and pull up.

    Editar

  10. Black and Decker WP900 Motor Replacement: passo 9, imagem 1 %32

    • With a large amount of force, pull the motor up and off of the wire coil.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Autor(a)

com 2 outros contribuidores

Stefan Wolowec

Membro desde: 02/15/16

128 Reputação

Autoria de 1 guia

Emblemas: 7

+4 outros emblemas

Equipe

IUPUI, Team 8-8, Wilson Spring 2016 Membro de IUPUI, Team 8-8, Wilson Spring 2016

IUPUI-WILSON-S16S8G8

Membros da 4

Autoria de 4 guias

Um comentário

Very straightforward tutotial. We are writing review of this product here https://www.helpful.reviews/en/product/4.... However we have not found many cases among owners of this product that they would need to repair motor by its replacement.

John Bazmek - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 14

Duração total: 2,261