Conserte seus objetos Comunidade Loja

Black and Decker One Step Steam Iron Temperature Regulator Replacement

Introdução

This guide will show you how to replace the temperature regulator in a Black + Decker One Step Iron.

Before replacing the temperature regulator, test each setting with your iron for about 10 minutes to see if it will begin to heat up properly. If it does not heat up at all with any setting, then you can assume that your iron is broken. The temperature regulator is something that can be easily broken or dented, due to overuse or damage.

Before beginning this guide, make sure that your iron is turned off and completely cooled down. If it is hot, remove the plug and allow the iron to sit upward and away from other objects for 30 minutes to cool significantly in order to reduce risk of injury.

O que você precisa

  1. Black and Decker One Step Steam Iron Temperature Regulator Replacement, Temperature Regulator: passo 1, imagem 1 %32 Black and Decker One Step Steam Iron Temperature Regulator Replacement, Temperature Regulator: passo 1, imagem 2 %32

    • Use a spudger to pry the three screw covers out of the iron.

    • Using force to remove the caps may be necessary. Do not worry if you hear popping sounds when removing them.

    Editar

  2. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 2, imagem 1 %32

    • Remove the three screws using a T5 Torx screwdriver.

    Editar

  3. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 3, imagem 1 %32

    • Pull the back cover off.

    Editar

  4. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 4, imagem 1 %32 Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 4, imagem 2 %32

    • Use a spudger to remove the clear rubber cover from the front of the iron.

    Editar

  5. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 5, imagem 1 %32

    • Remove the single screw located under the rubber cover using a Phillips #0 screwdriver.

    Editar

  6. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 6, imagem 1 %32

    • Remove the two screws holding the handle to the base using a Phillips #0 screwdriver.

    Editar

  7. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 7, imagem 1 %32

    • Remove the screws holding the plate to the base using a Phillips #0 screwdriver.

    Editar

  8. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 8, imagem 1 %32 Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 8, imagem 2 %32 Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 8, imagem 3 %32

    • Insert a spudger into the space in front of the pumps.

    • Pull down on the spudger so that the tab is visible.

    • Repeat for the other pump.

    Editar

  9. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 9, imagem 1 %32

    • Remove the two screws using a Phillips #0 screwdriver.

    Editar

  11. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 10, imagem 1 %32

    • Push the spray nozzle using the pointed end of a spudger.

    Editar

  12. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 11, imagem 1 %32

    • Remove the handle from the base.

    Editar

  13. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 12, imagem 1 %32

    • Remove the two pumps.

    Editar

  14. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 13, imagem 1 %32 Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 13, imagem 2 %32

    • Pry the white plastic cylinder out from its hole using a spudger.

    • The plastic cylinder is held in place by the plastic arm. Some force will be necessary.

    Editar

  15. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 14, imagem 1 %32 Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 14, imagem 2 %32

    • Using two spudger, pry the two plastic pieces holding the lever away from the lever.

    • Lift the lever out.

    Editar

  16. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 15, imagem 1 %32

    • Pull the lever and its attached pump out of the base.

    Editar

  17. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 16, imagem 1 %32

    • Remove the two screws using a Phillips #0 screwdriver.

    Editar

  18. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 17, imagem 1 %32

    • Insert a spudger in between the white plastic and the purple plastic.

    Editar

  19. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 18, imagem 1 %32

    • Rotate the spudger so that it separates the top of the white plastic from the bottom of the purple plastic.

    Editar

  20. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 19, imagem 1 %32

    • Move the spudger along the gap until you hear a popping noise.

    Editar

  21. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 20, imagem 1 %32

    • Verify that the tab is detached.

    Editar

  22. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 21, imagem 1 %32 Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 21, imagem 2 %32

    • Separate the white plastic from the bottom purple plastic.

    • Hold the top section (white and purple) steady with one hand.

    • Pull the plate (bottom) section toward the side with the tab shown in Step 20 until the plate is detached.

    Editar

  23. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 22, imagem 1 %32

    • Use the spudger to gently pop the pump connecter off of the plate.

    Editar

  24. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 23, imagem 1 %32

    • Remove the three visible screws using a Phillips #0 screwdriver.

    Editar

  25. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 24, imagem 1 %32

    • Remove the plate holder.

    Editar

  26. Black and Decker One Step Steam Iron Temperature Regulator Replacement: passo 25, imagem 1 %32

    • Remove the screw using a Phillips #0 screwdriver.

    • Remove the temperature regulator from the iron.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

4 outras pessoas executaram este guia.

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 9

Últimos 7 dias: 77

Últimos 30 dias: 228

Duração total: 4,502