Pular para o conteúdo principal

Introdução

If the tablet and keyboard of your device are not connecting properly, then you may need to replace the docking connectors on your device. Before attempting to replace the docking connectors, please visit the troubleshooting page, follow the directions under the heading Keyboard Does Not Dock Properly, and attempt any recommendations listed. If you have followed all of the instructions on the troubleshooting page and still have sporadic or non-existent communication between the tablet and keyboard, you can follow this guide to replace the docking connectors on your device.

Peças

Nenhum componente especificado.

  1. Remove the 8, 5.25 mm screws on the back cover using the screwdriver. Insert the opening tool into the USB port. Carefully remove the back cover using the opening tool.
    • Remove the 8, 5.25 mm screws on the back cover using the screwdriver.

    • Insert the opening tool into the USB port.

    • Carefully remove the back cover using the opening tool.

  2. Remove the yellow tape from the board cables. Carefully unplug the two board cables from their connectors by pulling on them. Carefully unplug the two board cables from their connectors by pulling on them.
    • Remove the yellow tape from the board cables.

    • Carefully unplug the two board cables from their connectors by pulling on them.

  3. Remove the 2, 4.25 mm screws on the left hand tab that are securing the dock in place. Remove the 2, 4.25 mm screws on the left hand tab that are securing the dock in place.
    • Remove the 2, 4.25 mm screws on the left hand tab that are securing the dock in place.

  4. kits de reparo de baterias de iPhone

    Only $29.99

    Buy Now

    kits de reparo de baterias de iPhone

    Only $29.99

    Buy Now
  5. Lift up the metal tab on the left side using the opening tool. Using your fingers may be easier than using the opening tool for this particular step, although both can be used. Using your fingers may be easier than using the opening tool for this particular step, although both can be used.
    • Lift up the metal tab on the left side using the opening tool.

    • Using your fingers may be easier than using the opening tool for this particular step, although both can be used.

  6. Remove the 2, 4.25 mm screws on the right hand tab that are securing the dock in place. Remove the 2, 4.25 mm screws on the right hand tab that are securing the dock in place.
    • Remove the 2, 4.25 mm screws on the right hand tab that are securing the dock in place.

  7. Lift the metal tab on the right side up using the opening tool. Using your fingers may be easier than using the opening tool for this particular step, although both can be used. Using your fingers may be easier than using the opening tool for this particular step, although both can be used.
    • Lift the metal tab on the right side up using the opening tool.

    • Using your fingers may be easier than using the opening tool for this particular step, although both can be used.

  8. Insert the opening tool between the two sections of the device. Lift up the keyboard section using the opening tool.
    • Insert the opening tool between the two sections of the device.

    • Lift up the keyboard section using the opening tool.

  9. Carefully pull up on the keyboard section using your hands to remove it from the screen section. Carefully pull up on the keyboard section using your hands to remove it from the screen section. Carefully pull up on the keyboard section using your hands to remove it from the screen section.
    • Carefully pull up on the keyboard section using your hands to remove it from the screen section.

  10. Pull the docking connector off of the screen section. Pull the docking connector off of the screen section. Pull the docking connector off of the screen section.
    • Pull the docking connector off of the screen section.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Grecia Corrada

Membro desde: 19-03-2018

1.020 reputação

6 Guias de autoria

Equipe

Baylor, Team S3-G3, Williams Spring 2018 Membro de Baylor, Team S3-G3, Williams Spring 2018

BU-WILLIAMS-S18S3G3

3 Membros

6 Guias de autoria

Where do you get the docking ports or whatever it is called? With the magnets

Michael - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 1

Últimos 7 dias: 6

Últimos 30 dias: 47

Todo: 612