Ir para o conteúdo principal

Conserte seus objetos

Direito de executar reparos

Loja

The G4 Quicksilver came in 533MHz, 667MHz, 733MHz, 800MHz, 933MHz, And 1.0GHz speeds.

66 Perguntas Visualizar todos

Upgraded 800Ghz G4 to a Dual 1Ghz G4 Processor with Kernal Panic?

I removed the 800Ghz G4 Processor then Replaced upgraded to Dual 1Ghz G4 Processor.

The system started with the Apple Chime and OSX 10.5.6 but then I received a kernel panic screen with errors.

Is this a OSX software nightmare?

Does the Operating System think it is trying to boot to a Single Processor? and gets confused about the Dual Processor? or was I supposed to change some settings via the sautering? scheme I have seen?

Please help....

I get White Buttons and the system just runs quiet.......

How do I get it to REINSTALL the OSX CD?

Responder a esta pergunta Também tenho esse problema

Esta pergunta é pertinente?

Pontuação 0
Adicionar um comentário

4 respostas

Pergunta Mais Útil

I would wipe it out and restore. But on a side note, did you reapply thermal grease for the new CPU?

Esta resposta foi útil?

Pontuação 1
Adicionar um comentário

no I did not.....is that needed? I didn't see any grease on either processor...but I would like to follow your process as I have heard that too on other system builds.......I didn't see it on this one.

I can find it at Fry's I am sure....

but can you please please tell me how to wipe it out and restore...

if the computer is not responsive....I mean I should have placed the CD in the Drive when I had the APPLE showing before the KERNAL PANIC.....

Now all I get is White Button and FAN noise.......

So I am unsure how to get back to the process of making the computer first OPEN The CD DOOR so I can PUT a CD INTO IT.....and then allowing it....

The keyboard seems unresponsive....so does the mouse....

Before it was in the programmers setting at Kernal Panic but Frozen....

So I shut down by pressing the power button.

Now when I repress the inside button for 30 secs........after unplug ofcourse....

I was going to try to RESET PRAM by holding the keys PRAM but again....I was not getting any response just the system turns on......

What should I do next to reinstall the OSX software?

thanks

Esta resposta foi útil?

Pontuação 0

Comentários:

Sorry about the late reply... I've been busy with school. Thermal grease is a MUST. It helps the heat dissipate from the CPU to the heatsink, without it you're going to overheat and possibly damage your computer. Getting it semi-responsive will have to be the first step.

por

Adicionar um comentário

Well I need to get the grease and re apply it and

What do I do if it is just giving me the white buttons?

Nothing?

I had another Mac do this to me too

I dunno what to do at this point

Instead of putting the old processor back

Do you in fact know if there is a problem with switching out a single processor to a DUo processor type configuration

The OSX was expecting the setup from the last restart

But I pushed the button inside the thing

Unplugged and many 30sec pauses

Holding the button

Even waiting a few days

Not powering this thing up again until I heard from you and had the grease on the CPU or tried replacing the other CPU to see if that was the issue

I really need the dual processor to work

I didn't leave the unit on very long when I tested it

As soon as the kernel panic happens I shut down but then I get that white button upon trying to start up again

What next?

Do I need clean harddrive in there? No OSX

How do I get it to respond to CDRom install?

If I just get white button and then nothing ?

Esta resposta foi útil?

Pontuação 0
Adicionar um comentário

I had the same problem and I checked the model and the processor was incompatible. Check the model and see if a dual GHz cpu is supported.

Esta resposta foi útil?

Pontuação 0
Adicionar um comentário

Adicionar a sua resposta

Singleton Makin será eternamente grato(a).
Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 0

Duração total: 419