Repair guides and support for your LG TV.

576 Perguntas Ver todas

No Power / No Standby Light (already tried PS Board) LG 47LA6200

Can someone suggest what to try next?

TV is an LG 47LA6200-UA.

Symptoms are: NO power at all. Not even the red LED standby light.

I already tried TWO replacement power supply boards and Nothing.

Still, no power at all and not even the red LED standby light. (See photos).

(I also tried a new power cord just in case - but nothing)

***What should I try next?***

Is it possible that the mainboard is the issue?

NOTE: I can probably dis-assemble and replace parts, but I’m NOT a technician and I don’t have sophisticated test equipment.

Thanks!

David

Block Image

Block Image

Respondido! View the answer Também tenho esse problema

Esta é uma boa pergunta?

Pontuação 0

Comentários:

FIXED!

[br]

The mainboard was the issue. I swapped out the mainboard and TV works great!

Thanks again for everyone’s help!

por

Adicionar um comentário
Spread Fixmas Cheer
Get $12 off your purchase of $50 or more with code FIXMAS12
Spread Fixmas Cheer
Get $12 off your purchase of $50 or more with code FIXMAS12

4 Soluções

Solução escolhida

FIXED!

I swapped out the mainboard and the TV works great!

Thanks again for everyone’s help.

Esta resposta foi útil?

Pontuação 0
Adicionar um comentário
Resposta Mais Útil

@djordan

yes it is absolutely possible. Since you already repalced the power board it is most likely a main board or a button bar/IR board issue. Start by measuring the voltage right at the fuse on your power board. This will make sure that you have power going to the board (just out of curiosity, you did check your outlet and tried a different outlet as well)

Block Image

Esta resposta foi útil?

Pontuação 2

Comentários:

Thank you irineo and oldturkey!

Excellent diagram oldturkey! I’m going to measure as you’ve directed when I have access again to the TV over next few days (at a buddy’s place). I might also order a mainboard to try it to see what happens.

(Also, confirmed that our power outlet is working - we tried at least a couple and other devices were plugged into the power bar).

Will report back - thanks again.

por

Adicionar um comentário

david , if you have multi tester check dc volts output at psu in between connection of psu and the mainboard if nothing the power supply is dead or same with that you bought … if there is supposed to be have standby lights ..

Esta resposta foi útil?

Pontuação 1
Adicionar um comentário

NEXT TROUBLESHOOTING STEPS?

Both the ORIGINAL board and the FIRST replacement board test properly (at the indicated test points)… (I didn’t test the SECOND replacement board because it didn’t have the same test points accessible on the power connector):

  • Finally set the TV up for testing on my table…

Block Image

*** ORIGINAL BOARD TESTING: First and Second test points:

Block Image

Block Image

  • FIRST REPLACEMENT BOARD TESTING: First and Second test points:

Block Image

Block Image

  • NOTE: Just to be sure I have the correct boards, I took close-ups of each. There seem to be minor differences. For example my ORIGINAL board is marked with “IT” (on the lower bottom edge per the photo); and the FIRST replacement board is marked “HE”. Not sure if that matters

ORIGINAL BOARD

Block Image


FIRST REPLACEMENT BOARD

Block Image


SECOND REPLACEMENT BOARD

Block Image

Esta resposta foi útil?

Pontuação 0
Adicionar um comentário

Adicionar a sua resposta

David Friedman será eternamente grato(a).
Visualizar Estatísticas:

Últimas 24 horas: 12

Últimos 7 dias: 61

Últimos 30 dias: 260

Todo: 567