Ir para o conteúdo principal

Conserte seus objetos

Direito de executar reparos

Loja

Ajuda

Versão atual de: jayeff ,

Texto:

Hi @rohitko ,
 
Do you get a manufacturer’s logo screen if you disconnect both SSD + HDD and start the desktop?
 
If so can you get into BIOS OK?
 
If not, you may have to source a system speaker and connect it to the motherboard to check for any beeps, as this will speed things up if there are any. See image below.
 
[image|2055615]
 
(click on image to enlarge for better viewing)
 
If you have a DMM (digital multimeter) and know how to use it, here’s how to [http://support.antec.com/support/solutions/articles/1000015319-is-my-power-supply-dead-the-paperclip-test|test the PSU] to see if it is outputting all the correct voltages.
 
=== Update (04/07/2020) ===
Here’s an image of the plug connection left speaker, right speaker and earth.
 
[image|2055656]
 
(click on image to enlarge)
 
Wire +speak on motherboard to tip (left channel)
 
Wire -speak on motherboard to sleeve (earth)

Status:

open

Editado por: jayeff ,

Texto:

Hi @rohitko ,
 
Do you get a manufacturer’s logo screen if you disconnect both SSD + HDD and start the desktop?
 
If so can you get into BIOS OK?
 
If not, you have a DMM (digital multimeter) and know how to use it, here’s how to [http://support.antec.com/support/solutions/articles/1000015319-is-my-power-supply-dead-the-paperclip-test|test the PSU] to see if it is outputting all the correct voltages.

You
may have to source a system speaker and connect it to the motherboard to check for any beeps, as this will speed things up if there are any. See image below.
If not, you have a DMM (digital multimeter) and know how to use it, here’s how to [http://support.antec.com/support/solutions/articles/1000015319-is-my-power-supply-dead-the-paperclip-test|test the PSU] to see if it is outputting all the correct voltages.

You
may have to source a system speaker and connect it to the motherboard to check for any beeps, as this will speed things up if there are any. See image below.
[image|2055615]
 
(click on image to enlarge for better viewing)
 
If you have a DMM (digital multimeter) and know how to use it, here’s how to [http://support.antec.com/support/solutions/articles/1000015319-is-my-power-supply-dead-the-paperclip-test|test the PSU] to see if it is outputting all the correct voltages.

Status:

open

Editado por: jayeff ,

Texto:

Hi @rohitko ,
 
Do you get a manufacturer’s logo screen if you disconnect both SSD + HDD and start the desktop?
 
If so can you get into BIOS OK?
 
If you have a DMM (digital multimeter) and know how to use it, here’s how to [http://support.antec.com/support/solutions/articles/1000015319-is-my-power-supply-dead-the-paperclip-test|test the PSU] to see if it is outputting all the correct voltages.
 
You may have to source a system speaker and connect it to the motherboard to check for any beeps, as this will speed things up if there are any. See image below.
 
[image|2055615]
 
(click on image to enlarge for better viewing)

Status:

open

Mensagem original de: jayeff ,

Texto:

Hi @rohitko ,

If you have a DMM (digital multimeter) and know how to use it, here’s how to [http://support.antec.com/support/solutions/articles/1000015319-is-my-power-supply-dead-the-paperclip-test|test the PSU] to see if it is outputting all the correct voltages.

You may have to source a system speaker and connect it to the motherboard to check for any beeps, as this will speed things up if there are any. See image below.

[image|2055615]

(click on image to enlarge for better viewing)

Status:

open