Pular para o conteúdo principal
Ajuda

Versão atual de: Tom ,

Título:

Help on iPhone 6 plus long screw damage

Texto:

Hello,
 
I recently ordered an iPhone 6 plus that I wanted to learn a bit of board repair on and sell it on as I usually do however I was hoping that this would only be a backlight filter replacement. I replaced the filters that needed replacing and the phone still has completely no backlight but you see the image when you put a torch to it. I have noticed there is long screw damage in the holes and I have got a diagram where the traces are.
 
Can anyone lead me through this repair as I'm unsure if I'm doing this correctly and I have also ordered some 0.1mm jumper wire that I think will be good for the traces. I have some pictures of the bottom right hole that I have tried to pick the layer off of but I don't see what is wrong with it. Can anyone please help me with this, I would be very grateful
 
[image|1267003]
 
[image|1267005]
 
[image|1267004]
[image|1267004]
 
[image|1267073]

dispositivo:

iPhone 6 Plus

Status:

open

Resposta Aceita:

441718

Editado por: Tom ,

Título:

Help on iPhone 6 plus long screw damage

Texto:

Hello,
 
I recently ordered an iPhone 6 plus that I wanted to learn a bit of board repair on and sell it on as I usually do however I was hoping that this would only be a backlight filter replacement. I replaced the filters that needed replacing and the phone still has completely no backlight but you see the image when you put a torch to it. I have noticed there is long screw damage in the holes and I have got a diagram where the traces are.
 
Can anyone lead me through this repair as I'm unsure if I'm doing this correctly and I have also ordered some 0.1mm jumper wire that I think will be good for the traces. I have some pictures of the bottom right hole that I have tried to pick the layer off of but I don't see what is wrong with it. Can anyone please help me with this, I would be very grateful
Can anyone lead me through this repair as I'm unsure if I'm doing this correctly and I have also ordered some 0.1mm jumper wire that I think will be good for the traces. I have some pictures of the bottom right hole that I have tried to pick the layer off of but I don't see what is wrong with it. Can anyone please help me with this, I would be very grateful
 
[image|1267003]
 
[image|1267005]
[image|1267004
[image|1267004]

[image|1267073
]
[image|1267004
[image|1267004]

[image|1267073
]

dispositivo:

iPhone 6 Plus

Status:

open

Editado por: Tom ,

Título:

Help on iPhone 6 plus long screw damage

Texto:

Hello,
 
I recently ordered an iPhone 6 plus that I wanted to learn a bit of board repair on and sell it on as I usually do however I was hoping that this would only be a backlight filter replacement. I replaced the filters that needed replacing and the phone still has completely no backlight but you see the image when you put a torch to it. I have noticed there is long screw damage in the holes and I have got a diagram where the traces are.
 
Can anyone lead me through this repair as I'm unsure if I'm doing this correctly and I have also ordered some 0.1mm jumper wire that I think will be good for the traces. I have some pictures of the bottom right hole that I have tried to pick the layer off of but I don't see what is wrong with it. Can anyone please help me with this, I would be very grateful

[image|1267003]
[image|1267005]
[image|1267004]
Can anyone lead me through this repair as I'm unsure if I'm doing this correctly and I have also ordered some 0.1mm jumper wire that I think will be good for the traces. I have some pictures of the bottom right hole that I have tried to pick the layer off of but I don't see what is wrong with it. Can anyone please help me with this, I would be very grateful

[image|1267003]
[image|1267005]
[image|1267004]

dispositivo:

iPhone 6 Plus

Status:

open

Postagem original de: Tom ,

Título:

Help on iPhone 6 plus long screw damage

Texto:

Hello,

I recently ordered an iPhone 6 plus that I wanted to learn a bit of board repair on and sell it on as I usually do however I was hoping that this would only be a backlight filter replacement. I replaced the filters that needed replacing and the phone still has completely no backlight but you see the image when you put a torch to it. I have noticed there is long screw damage in the holes and I have got a diagram where the traces are.

Can anyone lead me through this repair as I'm unsure if I'm doing this correctly and I have also ordered some 0.1mm jumper wire that I think will be good for the traces. I have some pictures of the bottom right hole that I have tried to pick the layer off of but I don't see what is wrong with it. Can anyone please help me with this, I would be very grateful

dispositivo:

iPhone 6 Plus

Status:

open