⟐ Answered fevereiro 25, 2015 at 8:45 GMT-7

About 75% of our parts end up getting returned to the parts supplier due to streaks on the glass and/or grease smudges around the edges of the inside of the digitizer. Fortunately they take them back and replace them no questions asked, but the replacements they send are just as bad and we still have to send a majority of those back as well.

I am wondering if theres other people here that have good relationships with parts suppliers that they would be willing to refer to me. We usually purchase the full digitizer assembly (w/ bezel, home button included). Any help would be great and I would be happy to let the suppliers know that you referred me.

Help me, iFixit community. You're my only hope.

Thanks.

⟐ Answer accepted fevereiro 10, 2015 at 15:09 GMT-7

⟐ Commented janeiro 31, 2015 at 7:21 GMT-7

Any ideas?

⟐ Answered janeiro 17, 2015 at 11:22 GMT-7

I have replaced the digitiser on an iPad mini 1st Gen following the iFixit guide closely, however approximately the top 5th of the screen is unresponsive to touch, below this the touch screen functions fine.

I have had a look at the digitizer socket which has no missing pins, also cleaned these incase there was some dirt obstructing the connection however the same problem occurred.

I have tried 2 different digitizers which have exactly the same problem. Have ordered a 3rd from a different supplier to see if it is a problem with the digitizer.

Would really appreciate any advice on this one, anyone had a similar issue?

Best regards,

Joe

⟐ Answered novembro 20, 2014 at 8:59 GMT-7

⟐ Answered agosto 26, 2014 at 14:33 GMT-7

I've been trying to purchase a handful of iPad Mini home button ribbon cables for a couple of iPads I'm repairing. Despite the name "home button ribbon cable", these cables have another function; they contain about eight tiny SMT parts which together detect the smart cover when it is closed or opened to shut off or turn on the iPad

I've shopped on eBay and received a total of ten (10) home button ribbon cables in the past three months from four different vendors. Every single one of them has been missing the smart cover parts. The photos shown in their ads show these parts fully populated, but when they come, they're unpopulated.

One vendor ("telitetech") took the time to understand the problem, checked and told me they did not have any working parts and gave me a refund.

One vendor ("top*parts") sent replacements, which were also bad. They refunded my money.

One vendor ("fine-stock") promised to send a replacement within 3-5 weeks and I should be patient (It's been 8 weeks. It hasn't arrived).

I am still in discussion with the final vendor as their defective parts just arrived.

I fear that some supplier has a defective lot of home button ribbon cables and, perhaps having been rejected by Apple, are now dumping them on eBay. The vendors handling these parts are themselves not aware that they are defective and if you complain, they just reach into the bin and send another set of defective parts.

Only one vendor ("telitetech") withdrew their defective parts from ebay and are now explicitly advertising that their cables have the missing parts (and if I'd noticed that before today I'd have just ordered tfrom them).

The takeaway-- it's buyer-beware in spare-parts world. Don't be afraid to complain if thngs aren't right. Most vendors really aren't trying to steal from you, but some just aren't equipped to help.

BTW, I have tried to transfer the SMT parts from old button ribbon cables to my unintended stock of blank cables, with mixed success so far (two attempts:one failure, one still awaiting test).

⟐ Answered junho 21, 2014 at 9:25 GMT-7

I haven't been able to fix after cleaning both the digitiser and LCD connectors on the main board, and have no other thoughts. I followed the guide to the most part, and was shocked when I put it all back together.

I have photos but am unsure how to post them.

Thankyou for any help.

⟐ Answered maio 10, 2014 at 2:47 GMT-7

The one in question was bought to me after a failed DIY fix. I have attempted to fit 3 different digitizers that work perfectly in other machines but without success.

The problem is very temperamental, sometimes the touch screen will work perfectly and at others not. I have attempted to apply pressure at different parts of the PCB without change, the ribbon clips and connectors look ok under magnification and I have restored the devise back to factory setting and updated. Nothing makes any difference.

Be grateful for any help and advice - many thanks Dan

⟐ Answered março 19, 2014 at 6:20 GMT-7

⟐ Answered abril 02, 2013 at 18:36 GMT-7

so a few months back (like 2-3 months) my dad got very mad (unexpected) and my ipad was on the table. he threw my ipad very hard into the floor (and the floor cracked along with my ipad). the corners of one half of the ipad was cracked (the other half wasn’t cracked as badly). and surprisingly and fortunately it still works (everything was normal except my microphone doesn’t work and the camera was blurry bc my mom had to tape near it and it sorta covered it).

so a day or two before, it started acting up. like i tried to unlock my ipad and i pressed one number (passcode) and the ipad itself just started spamming the passcode and i was forced to close it. i tried again and once again the ipad started spamming the passcode numbers and the try again after 1 minute lock came on. so i left it alone cuz i thought it would fix itself after a night. so yesterday morning i opened it, thinking it fixed itself because the passcode part had no problems. then after a few minutes, it started acting up. i went into safari— the search bar just went up and down and up and down (it wasn’t spamming letters it was just the screen). i tried roblox, went into adopt me, the starting screen kept on spamming me, every time i would press no the same question/sign would pop right back up (it’s not supposed to). for ex: it would say do u want to teleport to the hat shop yes or no and i would press no but the same sign kept on popping up so i couldn’t even play. the screen was moving itself. (spamming letters on my keyboard only happened once, just the passcode.)

help me is it just broken? yes i’ve tried shutting it down.

⟐ Commented janeiro 16, 2026 at 7:44 GMT-7

⟐ Commented novembro 20, 2025 at 16:34 GMT-7

⟐ Answer accepted março 22, 2025 at 14:15 GMT-7

I love my Nodus case that I've been using for the Air, but really want to get sleep/wake working again. I figure I'll add the extra magnets to make it work, but haven't been able to locate them.

⟐ Commented janeiro 14, 2025 at 16:57 GMT-7

⟐ Answered dezembro 09, 2024 at 14:55 GMT-7

⟐ Commented setembro 10, 2024 at 14:40 GMT-7

⟐ Commented agosto 28, 2024 at 3:58 GMT-7

I got three iPads lying around with various defects and I'm trying to make a single properly functioning one out of them.

• The iPad Air 2 LTE (A1567) has a near-dead battery
• The iPad 5th's (A1822) screen is cracked and loose every which way
• The iPad 7th (A2197), according to the Apple Store has a dead logic board (won't boot / goes into reboot cycle)

Far as I can tell my options are to either repair/replace 7's board or replace the Air 2's battery.

So I was wondering if the apparently different model battery from the iPad 5 would be okay to fit into the Air 2?

(Sorry if it's an obvious 'no way'. Not an expert by any stretch.)

Many thanks

⟐ Answered agosto 25, 2024 at 4:48 GMT-7

⟐ Commented agosto 21, 2024 at 10:41 GMT-7

⟐ Answered agosto 10, 2024 at 8:04 GMT-7