The printer works beautiful, except for when it isn't used for a couple days, which it will say "Offline". Troubleshooting in Windows 10 just says it's not powered on, but it clearly is. When I check the network status on the printer, it says still connected. I'm unable to ping it when it says offline.

Sometimes rebooting the router will cause it to come back, but usually I have to remove the printer completely, and re-add it manually using the IP Address. It doesn't come up as an addable device for some reason, which is the reason for manually adding it.

One possible fix I found said to go to the port configuration and disable SNMP. (SNMP Fix Tutorial)However, when I click on "Configure Port...", I get an error. Also, the port name is very odd looking.

I have a picture of the error located here = Port error

Is there something I can do to resolve this that I'm not aware of?

Thank you for the response. It makes complete sense.

So I deleted the printer, and re-added it using the hostname instead of the IP address. I have the epson software already installed, and it says all drivers are up to date. When I try to run the Epson Event Manager, with the printer added, it says

And I still get the following error when I try to configure the port =

I will let you know if/when it goes offline again.

This issue started before I ever started using the IP address to add it.

Thank you again for responding.

⟐ Answered abril 13, 2026 at 5:01 GMT-7

⟐ Answered dezembro 09, 2025 at 0:49 GMT-7

⟐ Answered agosto 01, 2023 at 6:05 GMT-7

I'm unable to get the printer to print to an envelope inserted in the rear paper feed slot. I've set the printer property "Paper Type" for Envelope, "Paper Source" for rear paper feed slot. And mixed these up. Always similar results. The envelope in the rear slot will be fed through without printing and then a sheet of paper from the cassette is printed on. Or get an error on the printer that the Paper Type doesn't match the paper in Cassette 1.

What is the secret sauce to print an envelope?

⟐ Commented dezembro 08, 2025 at 8:17 GMT-7

My epson printer L3110 having light paper blinking but already check all is good. No paper jammed or any object inside the paper slot. I check with system show : MEMORY CARD IS LOADING ERROR

so what should I do to get the printer is normal? And what the solution to solve this error.

This is new printer as i buy last month.

Hope can help and run as normal.

thank you

Rafi Haron

⟐ Answered agosto 18, 2023 at 0:10 GMT-7

I have an Epson L386 printer, connected to wireless network.

Unfortunately I made a reset to router and now I don't remember my previous password.

So at this point I can't connect my printer to network. I am searching for hours, and

I still haven't figured out how can I reset my printer to factory reset, since it is not connected to network.

Any ideas?

Best regards

⟐ Commented fevereiro 25, 2026 at 4:11 GMT-7

I am using Epson L220. I used one local black ink. So the head is completely blocked. Please suggest me what i need to do.

⟐ Commented outubro 30, 2023 at 19:43 GMT-7

⟐ Answered junho 18, 2022 at 13:26 GMT-7

⟐ Answer deleted dezembro 20, 2019 at 7:47 GMT-7

⟐ Answered setembro 19, 2019 at 15:27 GMT-7

⟐ Answer accepted abril 20, 2026 at 8:44 GMT-7

⟐ Answer accepted junho 28, 2024 at 6:47 GMT-7

⟐ Answer deleted agosto 29, 2018 at 1:28 GMT-7

I Recently had a paper jam in my Epson Workforce 645 3-in-one printer which was given to me for free.

After clearing the jam, i neglected to hold the two side springs together before pushing the paper jam panel back into place. I believe that I broke one of the white plastic "wheels" on the right side that "grabs" the paper from the paper try.

I now have a permanent "paper jam" due to the misfeed.

This printer was free. My questions are:

1. is it repairable?

2. is it worth it given the fact that the printer was free.

⟐ Answered maio 27, 2020 at 7:14 GMT-7

⟐ Answered novembro 06, 2021 at 15:01 GMT-7

Cannot install Epson printer WF-2540 setup will not fully install the drivers. I have this problem on both computers. Before when I had windows 8 I had no problems, I upgraded to windows 10 cannot get printer to work. What can I do?

⟐ Answer deleted setembro 04, 2018 at 12:31 GMT-7

Epson Stylus Photo P50

⟐ Commented outubro 18, 2023 at 8:30 GMT-7

My Epson Workforce 3620 stopped printing clearly, with words in a Microsoft document printing with lines through them and spotchy to where you can't read some sentences in a full document.

It randomly started doing it so I replaced the ink cartridges and it has continued to do it. I know how to replace the ink cartridges as I pulled off the yellow "Remove" sticker and kept everything else, of course inserting it with the top-label side facing me until I heard a click.

I have used the "Maintenance" settings multiple - and by that I mean, roughly 30 or so - times of each Print Head Alignment (vertical & horizontal), Head Cleaning, Nozzle Check, and the roller cleaner option.

At first, I called Epson Customer Service. The person walked me through the maintenance steps, though I had done them several times, and told me that it must be the ink cartridges so they sent me all new ones free of charge. When I put them in, the issues were still happening and I ran through the maintenance settings again. When I called Epson back and provided a reference number, they had no idea what reference number I had and had me running through the maintenance steps again though I had assured them it was more than that, I work from home, need to get it fixed. I swear to you, this lady insisted that I must re-try the maintenance settings after already doing it one the phone with her and telling her that I did them on my own. There are no Epson repair centers in my area as well.

Has anyone else had this problem? Do you know of anything I can do? I am not really able to just buy a new one, since i just bought this one in December of 2017.

Thank you

⟐ Answered agosto 26, 2020 at 14:01 GMT-7

⟐ Commented novembro 25, 2023 at 18:21 GMT-7

if someone can help me figure this out i would appreciate it

my epson XP-960 printer its printing out with blue cast color on all prints including colored and black white photos , i had just re-installed new inks which are not epson inks but worked with before with no issues , funny thing is when i change my printing settings to print in "plain paper" colors come out ok on my black white photos and colored ones but the printing quality is bad with bands or stripes across , when i change the paper quality to either premium glossy or ultra premium photo paper prints come out with a blue cast , on my colored prints all colors are visible/printed but they have a very strong blue tint they look horrible and the black white come out blue , its really strange and i tried printing with several printing papers including epson premium photo paper , kodak and even HP same thing happens , i did do a nozzle check and cleaned the printing head and all comes out good i just feel im wasting printing paper trying to fix this.

⟐ Answer edited abril 18, 2023 at 16:17 GMT-7