iFixit - Answers With Device "Dyson Vacuum"

Dyson SV12: permanently repair a broken bin release slide catch on Dyson SV12

Mon, 17 Aug 2026 02:28:35 -0700

If your Dyson V10 or V11 bin slides completely off when you try to empty it because the red plastic stop catch snapped, don't buy an expensive new cyclone assembly. You can permanently fix it for pennies using a piece of standard plastic pipe.

By using a specific type of glue called plumbers' pipe welding solvent cement, the new part chemically melts and fuses directly to the Dyson plastic body, making it incredibly strong.

Materials Needed:

A scrap piece of 63mm plastic rainwater downpipe (the curvature perfectly matches the cylindrical Dyson body).
Plumbers' pipe welding solvent cement.
A fine-tooth junior hacksaw (or bandsaw) and a hand file (or grinding wheel).

How to Make and Fit It:

Cut the Stop Bar: Cut a small rectangle from the 63mm pipe that is exactly 44mm wide and 10mm long. Do not make it longer than 10mm, or the red handle won't be able to lift over it when you actually want to remove the bin for cleaning.
Shape the Edges: Use your file or grinding wheel to bevel (ramp) the front leading edge. Keep the back edge perfectly square. The ramp lets the bin slide back on smoothly, while the square edge acts as the stop.
Prep the Plastic: Lightly sand the slide track on the Dyson and the bottom of your new plastic piece. Clean both surfaces with rubbing alcohol to remove grease.
Glue and Position: Apply a thin layer of solvent cement to both parts. Press the piece onto the slide track. The square stop edge must sit exactly 44mm away from the front edge of the Dyson slide track.
Cure: Hold firmly for 60 seconds. Leave it alone for 24 hours to fully cure before putting the vacuum back together.

Why this works: Under normal use, the square edge stops the bin from falling off. But because the piece is only 10mm long, you can still pull firmly to let the red handle flex up and clear the stop when you purposefully want to remove the bin for cleaning! See video here https://files.catbox.moe/l7sa98.mov

Dyson V6 Motorhead: Why is my Dyson going on an off when I'm holding the on button?

Thu, 13 Aug 2026 20:31:02 -0700

Why is my Dyson going on an off when I'm holding the on button?

First let me say, the battery charges just fine and I’ve totally cleaned out the collection bin. I push the button to turn on the vacuum and it works, but then turns off and on over and over again while I’m still holding the button down.

I looked this up online and someone said the filter needed to be cleaned. So I took out the filter rinsed it as the online instructions said, let it dry, then put it back in. This did not solve the problem.

Any other suggestions?

⟐ Commented agosto 13, 2026 at 20:31 GMT-7

Dyson V15 Detect: Dyson V15 Detect stops after a few seconds with no indicators

Wed, 12 Aug 2026 06:01:37 -0700

I've had it for nearly 2 years. The problem occurs when I press the trigger—it runs for a few seconds and then stops (with its signature "wooump" sound). It repeats this 2-3 times before eventually working. However, now I can't get it to run for longer than a few seconds, even after several tries.

I’ve changed the filter and cleaned everything I can access. In some forums, I’ve read that it might be an issue with the "main body," (whatever that means) while others suggest it could just be a cracked trigger, which should be an easy fix.

⟐ Commented agosto 12, 2026 at 6:01 GMT-7

Dyson V11 Animal: Vacuum rollers are only working on turbo mode

Mon, 10 Aug 2026 09:57:06 -0700

My Dyson vacuum rollers only work on turbo mode

⟐ Commented agosto 10, 2026 at 9:57 GMT-7

Dyson DC20: Replace the hose in the vacuum head - where to order this hose?

Fri, 31 Jul 2026 23:38:02 -0700

My vacuum cleaner is still 100%, but the head doesn't work well anymore because the internal head is broken. Where to order?

Dyson DC58: The power keeps cutting out after a few seconds

Wed, 15 Jul 2026 14:24:21 -0700

The battery is fully charged.

We press the trigger button and the the hoover works for a few seconds and then stops. It does this consistently

⟐ Answered julho 15, 2026 at 14:24 GMT-7

Dyson Vacuum: Red lever will not pull up so I can empty/replace canister

Mon, 13 Jul 2026 14:28:52 -0700

I cannot empty my V8 canister because the red lever will not budge will I try to pull it up. Dyson is sending me a new canister, but have no idea how I can change it because you have to pull the red lever to release the current one.

⟐ Answered julho 13, 2026 at 14:28 GMT-7

Dyson V8 Absolute: bin/canister will not open no matter how hard we pull

Mon, 13 Jul 2026 09:57:14 -0700

I cannot open the bin/canister of my Dyson V8 Absolute to empty the contents. The trigger does not budge. We tried the little red latch on the bottom of the bin/canister but it’s blocked. We cannot detach the canister as the top red trigger is blocked. I bought it in June last year so still under guarnatee. Dyson told me to send it to them, which I am reluctant to do.

Any ideas how to open it without destroying it? It’s been a week of pulling the trigger so really fed up at this point.

⟐ Answered julho 13, 2026 at 9:57 GMT-7

Dyson V8 Absolute: The bin won’t open it appears to be severely jammed

Mon, 13 Jul 2026 08:52:28 -0700

When I try to pull on the tab to open the bin it won’t move it appears to be jammed and I can clean out the hover which is a major problem

⟐ Commented julho 13, 2026 at 8:52 GMT-7

Dyson DC41 Animal Total Clean: replace the latch to canister- 2 red pieces

Sun, 12 Jul 2026 07:01:49 -0700

Where can I find instructions for this

I have the parts

⟐ Answered julho 12, 2026 at 7:01 GMT-7

Dyson DC35: Dyson DC35 Stalling Repeatedly

Tue, 30 Jun 2026 08:26:47 -0700

This vacuum has a clean filter, clean brush, clear canister, charged battery. No matter what I do, it only works for about ten seconds before it shuts off, then I can start it again, but the cycle continues with it stalling, and stalling.

⟐ Commented junho 30, 2026 at 8:26 GMT-7

Dyson V15 Detect: What is the capacitance of this surface mount ceramic capacitor?

Sun, 28 Jun 2026 23:30:57 -0700

I damaged a very small ceramic capacitor cleaning the board. Does anyone know its rating/values or can measure them on a voltmeter?

Thanks

Dyson DC14: Dyson DC14 beater brush bar won’t STOP spinning.

Sun, 21 Jun 2026 14:50:04 -0700

DC14 Animal Upright beater brush bar typically stopped spinning when the vacuum was placed in the upright position (as expected). Now the beater brush no longer turns off when I stand the vacuum up to use the wand. Vacuum is also making a slight high-pitched sound for first minute or two after being powered on; not sure if any correlation but mentioning since this began maybe a month or two before I realized beater bar wasn’t stopping. I’ve taken it all apart & cleaned it well. No problem there as we have five girls with long hair & have to clean it often anyway. My best thought was the clutch, but all signs I can find online of a bad clutch point to bar *not* spinning. I have the opposite problem. Any ideas? Cannot find ANYONE with this issue online so not sure if I should go through hassle of replacing clutch or not in case it’s a different issue. What part makes the beater bar stop when the vacuum is placed in upright position?

⟐ Answered junho 21, 2026 at 14:50 GMT-7

Dyson Ball Animal 2 Total Clean: No suction from wand

Wed, 17 Jun 2026 13:12:39 -0700

Why is my wand has no suction?

Dyson DC14 All Floors: dyson dc14 soleplate placement

Sat, 13 Jun 2026 15:36:52 -0700

how to put a dyson dc14 soleplate back on the vacuum

Dyson v6 Absolute: How do I snap the canister lid back on it fell off

Wed, 10 Jun 2026 11:29:54 -0700

How to replace canister lid on my Dyson V6 it looks like it snaps back in but it's hard and don't want to break it

⟐ Commented junho 10, 2026 at 11:29 GMT-7

Dyson Micro 1.5kg: My carpet head wiii not spi

Fri, 05 Jun 2026 04:54:55 -0700

My carpet head will not spin

Dyson DC14: Brush bar is extremely noisy

Wed, 03 Jun 2026 16:43:38 -0700

If I use the telescope handle, it works fine but when I want to vacuum the floor and I turn on the brush bar, it's extremely loud; like it's screaming.

⟐ Answer accepted junho 03, 2026 at 16:43 GMT-7

Dyson Outsize: Why doesn’t the brush rotate

Mon, 01 Jun 2026 12:09:57 -0700

How can I get the brush to rotate?

Dyson 360 Eye: Eye 360 Red light flashing

Fri, 29 May 2026 03:43:06 -0700

Hi, trying to start the robot, a red flashing light appears and blocks any other operation. Occasionally the robots starts and it works normally for about a couple of hours covering the entire surface: this leads me to exclude battery issues but I would appreciate your support in finding the root cause of the red light. Could it be any issue related to the tracks? Thank you for you support