⟐ Commented agosto 17, 2024 at 19:27 GMT-7

⟐ Answer edited fevereiro 16, 2026 at 13:52 GMT-7

• Checked that lines are not clogged
• verified water pressure to inlet valve
• replaced float switch
• replaced water inlet valve

Then I began to wonder if I had a drain problem, that may cause my dishwasher to keep from filling, so I verified that the drain line was not obstructed and I checked resistance on my drain motor (33 Ohms, which I believe is fine). The dishwasher was not full of water, only a bit in the line…

Not sure what to do next…?

Help and thanks!

KDTM354DSS3

Thanks!

⟐ Commented maio 25, 2024 at 10:30 GMT-7

Dishwasher started to have some issues a few months back when we were not able to change cycle settings. This was not an issue since we always run on 'Normal' and 'Heated Dry'. However, a couple of days ago I noticed lights on right side of the panel were randomly flashing for a quick second. I just ignore it because cycle was running normal.

Now dishwasher wont start unless I do these steps:

1. Reset it by turning power off and back on (from electric board switch) when door is open

1. Closing door (a noise similar to draining will start)
2. Pushing cancel button (noise will stop)
3. Pushing start button (and a cycle start)

Cycle will clean dishes as normal with heated dry, like there were no issue. However if I want to start another cycle, I'll need to do above steps again.

Also lights will show very random patterns during the whole cycle as shared in the images.

What do you suggest?

⟐ Commented março 03, 2024 at 22:53 GMT-7

⟐ Answer edited outubro 03, 2023 at 10:43 GMT-7

⟐ Commented agosto 12, 2023 at 14:43 GMT-7

I also see it could be the thermostat, where is that located in my model?

⟐ Edited março 15, 2024 at 13:28 GMT-7

⟐ Commented janeiro 11, 2023 at 14:57 GMT-7

A. Blockage in Drain Hose:

1) I used the "Cancel/Drain" option successfully once and then this option stopped working too.

2) I found the drain hose clogged at the end connecting to the garbage disposal (there is no air gap). I cleaned the guck and tested it end to end for clear movement of water.

3) When I ran the Dishwasher, it still wouldn't drain (and pressing the "Cancel/Drain" button produced a soft vibration hum, likely due to the drain pump motor trying to run?)

B. Drain Pump Running Intermittently:

I pulled out the dishwater and extracted the drain pump out (Part #W10724439). I fond nothing impeding the movement of the impeller.

1) While holding the drain pump, when I pressed the "Cancel/Drain" button, the impeller worked for about 15 sec and stopped. However, I could feel the vibration from the motor unit. When I nudged the impeller wings, it would start running again.

I tested it a few times using the "Cancel/Drain" button and found the behavior inconsistent. Sometimes, it would run continuously and sometimes, stop (and start running again if I nudged it).

2) I unplugged the drain pump from the dishwasher and pried open the back plate of the impeller and found a very thin dry residue (looked like soap scum) around the circumference. I cleaned it (attached pic)

3) I then hooked it up directly to a 120V source. Every time I switch on the power, it runs continuously without any interruption.

I am now stuck and unsure what to look for next. Would appreciate some pointers.

⟐ Commented dezembro 29, 2022 at 8:42 GMT-7

I have a Frigidaire Model# FDB1500LFB0 and my problem is that…

after loading and selecting my cycle and hitting Start, my washer fills with water to the (I presume) proper amount of water in the bottom. The water is very hot. Then the system stops, and the only thing that will happen after opening it after this (anywhere from 3-15 minutes, I did this several times.) is that when the door is shut back and cancel pressed it will drain as normal. It was left to “run” once and the soap drawer opened, dumping the “pod” directly below it. The dishes had never had water on them and the “pod” was mushy from the ambient humidity, and in a spot directly under the drawer. If left on it will cycle through a fill/drain cycle but the spray-arms never move. I have cut the breaker to it on and off with no change.

Any help will be appreciated, thank you.

⟐ Edited maio 21, 2024 at 9:22 GMT-7

⟐ Commented junho 24, 2022 at 6:11 GMT-7

⟐ Answer edited maio 17, 2024 at 9:14 GMT-7

I have a Whirlpool ADG 8532/1 IX W(?) dishwasher.

The lights on the display are on if I push the door out.

But if I close the door it shuts down, so I guess there could something with the display?

Any suggestions?:D

⟐ Answered março 07, 2022 at 17:59 GMT-7

My Kenmore Elite dishwasher just stopped working and I went looking around and found that the power cord had begun to melt and was all black and scary looking. I’m looking to replace this if anyone has any experience or insight it would be greatly appreciated. Dishwasher is already installed and not by myself so I don’t know where to begin and if this requires the unit to be removed or not.

I believe Model is #66512773K311

⟐ Edited março 18, 2024 at 10:39 GMT-7

⟐ Commented setembro 30, 2021 at 15:15 GMT-7

⟐ Answered setembro 17, 2021 at 8:49 GMT-7

Tried reset by pressing three buttons next to START button and received error codes. F9 E1.

Any idea?

⟐ Commented julho 29, 2021 at 14:08 GMT-7

⟐ Answer edited fevereiro 08, 2021 at 8:07 GMT-7

⟐ Answer edited março 23, 2020 at 2:58 GMT-7

⟐ Answered dezembro 11, 2019 at 22:58 GMT-7