⟐ Answered março 06, 2026 at 15:29 GMT-7

Sempre que ligo a maquina para retirar o cafe, noto que ela vaza água perto do reservatório de água. Já a desmontei para ver se havia alguma fuga ou tubo gasto mas não. Não encontro nada. Coloquei a máquina em funcionamento desmontada e o certo é que fica tudo cheio de água e continuou a vazar sem indícios de onde se encontrara a fuga.

⟐ Commented janeiro 11, 2026 at 21:55 GMT-7

⟐ Commented dezembro 16, 2025 at 16:13 GMT-7

⟐ Answered fevereiro 24, 2024 at 8:18 GMT-7

Translation

The steam rod is broken and the machine has jammed. How can I solve it? Thank you

⟐ Answer accepted novembro 28, 2023 at 4:54 GMT-7

Tenho uma cafeteira expresso MEGASTAR {IDÊNTICO a CAFETEIRA ETERNY CM 508; ZEEX MANUAL BUON PALATO CM 508; e o tal de HUAYU CM 508 - fotos anexas} com o seguinte defeito: pressionado a botão POWER o mesmo “não prende”, em função disso não aquece . . .

Resido em São Carlos-SP-Brasil, e, não encontro ninguém para fazer o reparo . . . Como resolver? . . . Podem me indicar alguma Assistência Técnica aqui no Brasil?

OU, fornecer desenho de montagem/componentes para viabilizar uma "desmontagem sem estragos"?

Na eventual falta de componente, concordo até com o “quebra-galho” de “ligar direto” {jampear} os contatos desse interruptor, adaptando uma “chave pera” no cabo de força, uns 15 cm da base da cafeteira – ai a liga/desliga seria feita pela chave pera . . .

Cordialmente,

Tamas Harsany

tamash@terra.com.br

Google Translation

Good afternoon . . .

I have an espresso machine MEGASTAR { IDENTICAL to ETERNY MAKER CM 508 ; ZEEX MANUAL BUON PALATE CM 508 ; and such of HUAYU CM 508 - photos enclosed} with the following error: Pressing the POWER button the same " does not hold " , because it does not heat up . . .

I live in São Carlos -SP-Brazil , and can not find anyone to do the repair. . . How to solve? . . . Can show me some technical assistance, here in BRazil ?

OR , supply mounting design / components to enable a " disassembly without damage " this machine ?

The possible lack of component , I agree to with the " quick fix " of "direct connect " { jumping } contacts that switch , adapting a " pear key " in the power cord , about 15 cm from the base of the coffee - ai league / off would be made by pear key . . .

Sincerely,

Tamas Harsany

tamash@terra.com.br

⟐ Edited by author setembro 07, 2016 at 23:46 GMT-7

⟐ Answer edited maio 18, 2026 at 23:55 GMT-7

I have noticed that some of the coffee is leaked into the collector basket. In between the nossle and the brewing unit. I have taken the machine apart and tried to install a new brewing unit but some coffe Is still leaked into the collector basket. I have tried to clean the plate that punctures the pod but still coffee leakage happens. Any idea what could cause this and how I can fix it?

Be

Fredrik

I found mentions of the motor not being properly aligned.

The official FAQ states: The motor might not be in the correct position. Check if the water tank is filled and if the drip tray is in place. Turn the appliance OFF and then ON again. Then simultaneously press the button for My-Coffee and the on/off button for more than 2 seconds. The motor will move into the correct position. Insert the brewing unit again and check that it is correctly locked in position.

However, this proposed solution did not reset the motor position in my case.

I found that the locking handle of the brewing unit moves a metal lever.

This metal lever engages a button in the machine.

By carefully pressing this button (i used the handle of a small spoon), the motor reset to the correct position.

Long story short: I don't have a question, and just wanted to post this here for future reference.

⟐ Commented maio 18, 2026 at 1:32 GMT-7

The handle/lid area seems like a likely candidate, but I cannot see any obvious anchor points or hooks where it should be reattached. Where exactly does this spring belong, and what are the steps to reattach it? Does it require partial disassembly of the head/handle housing to access the mounting points?

⟐ Commented maio 17, 2026 at 15:52 GMT-7

⟐ Answered maio 16, 2026 at 20:24 GMT-7